A gravity bong is a type of water pipe that uses gravity to fill the chamber with smoke. It is made by attaching a bowl to a bottle and filling the bottle with water. The water pushes the smoke into the bottle and then into your lungs when you inhale.
Gravity bongs can be made with any type of plastic bottle and any type of bowl. The most common way to make a gravity bong is to use a plastic bottle and a bowl made from aluminum foil. You can also use a glass bottle and a bowl made from glass, metal, or ceramic.
The advantage of using a gravity bong is that it is very easy to make and does not require any special equipment. Gravity bongs are also very efficient at delivering THC-rich smoke into your lungs.
Supplies Needed for Making Your Own Gravity Bong
In order to make your own gravity bong, you will need the following supplies:
-A plastic bottle (2 liter soda bottles work well)
-A bowl (aluminum foil, glass, metal, or ceramic will work)
-A knife
-A pen or marker
-Scissors
-Tape
-A lighter
Instructions for Making Your Own Gravity Bong
1) Cut the bottom off of the plastic bottle using the scissors. If you are using a 2 liter soda bottle, cut the bottom inch off of the bottle. 2) Use the knife to make a hole in the side of the bottle. The hole should be big enough to fit the bowl snugly. 3) Tape the bowl to the side of the bottle so that it is airtight. 4) Fill the bottle with water until it is about an inch from the top of the bowl. Be sure not to get any water in the bowl! 5) Light your cannabis and place it in the bowl. 6) Put your mouth over the top of the bottle and slowly turn it upside down so that the water goes into the bowl. 7) Inhale slowly as you turn the bottle back upright. Be careful not to inhale too much at once or you may start coughing! 8) Enjoy your gravity bong hit! When you’re done, simply dump out the water and recycle your materials.
Conclusion: Making your own gravity bong is a great way to enjoy cannabis if you don’t have access to traditional smoking methods like pipes or joints. Gravity bongs are also very efficient at delivering THC-rich smoke into your lungs. With just a few household supplies, you can easily make your own gravity bong at home.
Are you looking to add a new twist to your smoking routine? If you’re a fan of marijuana, then you’ve likely already tried out a gravity bong. If not, then you’re in for a treat! A gravity bong is a type of smoking device that uses gravity to fill a chamber with smoke. Gravity bongs can be made at home with a few simple supplies. In this article, we’ll show you how to make your own gravity bong at home.
What Is A Gravity Bong?
A gravity bong is a type of smoking device that uses gravity to fill a chamber with smoke. The name “gravity bong” comes from the fact that the device relies on gravity to work. Gravity bongs can be made at home with a few simple supplies. The most common type of gravity bong is made with a plastic bottle and a bucket of water.
How Does A Gravity Bong Work?
Gravity bongs work by using the principles of Bernoulli’s principle. This principle states that when the speed of a moving fluid (in this case, air) increases, the pressure within the fluid decreases. The decreased pressure causes the liquid (smoke) to be drawn into the bottle. As more smoke is drawn into the bottle, the pressure inside the bottle increases and the liquid is forced out through the holes in the bottom of the bottle. This process continues until the chamber is full of smoke.
Instructions For Making A Gravity Bong
You will need:
-A plastic bottle
-A sharp knife
-A bucket of water
-Marijuana
1) Cut the bottom off of the plastic bottle with a sharp knife. Be sure to cut at an angle so that the hole is larger at the bottom than it is at the top. 2) Cut three small holes in the side of the bottle near the top. These holes will be used to draw air into the bottle and to release smoke from the chamber. 3) Fill the bucket with water and place the bottle upside down in the water so that only the top of the bottle is exposed. 4) Pack marijuana into bowl and light it. 5) Put your mouth over one of the holes on the side of The Girodrome 6) Light marijuana bowl and draw air into The Girodrome 7) Take your mouth off of The Girodrome8)Release Smoke 9)Repeat as necessary until chamber is full of smoke 10)Remove from water and inhale deeply from top hole 11)Enjoy your homemade gravity bong!
Conclusion: DIY: Make Your Own Gravity Bong AtHomeWe hope you enjoyed this tutorial on how to make your own gravity bong at home! If you follow these instructions, you’ll be sure to have a great time indulging in some delicious marijuana smoke. Remember to take it slow at first and enjoy your experience!
